Rki-instruments 35-3000RK-LEL/O Instrukcja Użytkownika

www.rkiinstruments.com35-3000RK-LEL/OSample-Draw DetectorOperator’s ManualPart Number: 71-0223RKRevision: P1Released: 2/28/11

6 • 35-3000RK-LEL/O Sample-Draw DetectorNOTE: The pump and pressure switch are factory-wired to the circuit board. See “Installation” on page 7 for a

35-3000RK-LEL/O Sample-Draw Detector • 7InstallationThis section describes procedures to mount the sample-draw detector in the monitoring environment

8 • 35-3000RK-LEL/O Sample-Draw Detector5. Slightly loosen the screw that secures the mounting foot to the housing, then rotate the mounting foot 180

35-3000RK-LEL/O Sample-Draw Detector • 9CAUTION: Do not route controller power wiring and detector wiring through the same hub. The power cable may

10 • 35-3000RK-LEL/O Sample-Draw DetectorStart UpThis section describes procedures to start up the sample-draw detector and place the sample-draw det

35-3000RK-LEL/O Sample-Draw Detector • 11for the oxygen channel, continue with step 3.3. Perform a zero operation at the controller. See the controll

12 • 35-3000RK-LEL/O Sample-Draw DetectorPerforming the response test1. Screw the demand flow regulator into the combustible gas calibration cylinder

35-3000RK-LEL/O Sample-Draw Detector • 136. If the fail condition continues, contact RKI Instruments, Inc. for further instruction.Slow or No Respons

14 • 35-3000RK-LEL/O Sample-Draw Detector11. Turn on the controller.CAUTION: Allow the replacement sensor to warm up for 15 minutes before you contin

35-3000RK-LEL/O Sample-Draw Detector • 156. Insert the cone-shaped front ferrule on top of the bottom ferrule. Insert the ferrule so the smaller end

35-3000RK-LEL/O Sample-Draw DetectorWARNINGRead and understand this instruction manual before operating detector. Improper use of the detector could

16 • 35-3000RK-LEL/O Sample-Draw DetectorCalibration, Combustible SensorThis section describes how to calibrate the combustible sensor in the sample-

35-3000RK-LEL/O Sample-Draw Detector • 17Returning to Normal Operation1. Reconnect the incoming sample line.2. Wait approximately one minute to allow

18 • 35-3000RK-LEL/O Sample-Draw Detector5. Disconnect the sample tubing from the sample-draw detector’s inlet fitting.6. Reconnect the incoming samp

35-3000RK-LEL/O Sample-Draw Detector • 19Parts ListTable 2 lists replacement parts and accessories for the sample-draw detector.Table 2: Parts ListPa

35-3000RK-LEL/O Sample-Draw DetectorProduct WarrantyRKI Instruments, Inc. warrants gas alarm equipment sold by us to be free from defects in material

35-3000RK-LEL/O Sample-Draw DetectorTable of ContentsOverview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

35-3000RK-LEL/O Sample-Draw Detector • 1OverviewThis operator’s manual describes the 35-3000RK-LEL/O sample-draw detector. This manual also describes

2 • 35-3000RK-LEL/O Sample-Draw DetectorDescriptionThis section describes the components of the sample-draw detector. The sample-draw detector consis

35-3000RK-LEL/O Sample-Draw Detector • 3Flow SystemThe sample-draw detector’s flow system consists of the INLET fitting, hydrophobic filter, pump, fl

4 • 35-3000RK-LEL/O Sample-Draw DetectorStatus LightsTwo status lights are above the flowmeter. They are also visible through the window in the housi

35-3000RK-LEL/O Sample-Draw Detector • 5ConnectorThe top of the sensor includes five pins that plug into the socket connector. This connector allows