Rki-instruments 35-3001A-01-01 Instrukcja Użytkownika

www.rkiinstruments.com35-3001A-01-01Methane Sample-Draw DetectorOperator’s ManualPart Number: 71-0310RKRevision: P4Released: 9/17/14

6 • 35-3001A-01-01 Methane Sample-Draw DetectorSpan PotThe span pot is located below the zero pot (see Figure 1). Use a small flat blade screwdriver

35-3001A-01-01 Methane Sample-Draw Detector • 7InstallationThis section describes procedures to mount the sample-draw detector in the monitoring env

8 • 35-3001A-01-01 Methane Sample-Draw Detector2. Close and latch the housing door.NOTE: The sample-draw detector is shipped with the mounting feet “

35-3001A-01-01 Methane Sample-Draw Detector • 9ring, if it came out, in the orientation shown in Figure 4. 4. Screw the inlet fitting tube nut back

10 • 35-3001A-01-01 Methane Sample-Draw DetectorInstalling the Exhaust Line1. Loosen the nut on the exhaust fitting until 3 threads are visible.2. Pu

35-3001A-01-01 Methane Sample-Draw Detector • 118. Connect the wires to the applicable detector/transmitter terminal strip at the controller as show

12 • 35-3001A-01-01 Methane Sample-Draw DetectorStart UpThis section describes procedures to start up the sample-draw detector and place the sample-d

35-3001A-01-01 Methane Sample-Draw Detector • 136. If necessary, use a small flat-blade screwdriver to adjust the zero potentiometer until the voltm

14 • 35-3001A-01-01 Methane Sample-Draw Detector4. Use the following formula to determine the correct test points output for the test sample.Output (

35-3001A-01-01 Methane Sample-Draw Detector • 154. Calibrate the sample-draw detector as described in “Calibration” on page 18.5. If the fail condit

35-3001A-01-01 Methane Sample-Draw DetectorWARNINGRead and understand this instruction manual before operating detector. Improper use of the detector

16 • 35-3001A-01-01 Methane Sample-Draw Detector9. Turn on power to the controller and place it into normal operation.10. Turn on the controller.CAUT

35-3001A-01-01 Methane Sample-Draw Detector • 1710. Turn on power to the controller.11. Turn on the controller and place it into normal operation.12

18 • 35-3001A-01-01 Methane Sample-Draw DetectorCalibration FrequencyAlthough there is no particular calibration frequency that is correct for all ap

35-3001A-01-01 Methane Sample-Draw Detector • 19voltmeter reading is 100 mV (± 2 mV). If you used a zero air calibration cylinder to set the zero re

20 • 35-3001A-01-01 Methane Sample-Draw DetectorParts ListTable 2 lists replacement parts and accessories for the methane sample-draw detector.Table

35-3001A-01-01 Methane Sample-Draw DetectorProduct WarrantyRKI Instruments, Inc. warrants gas alarm equipment sold by us to be free from defects in

35-3001A-01-01 Methane Sample-Draw DetectorTable of ContentsOverview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

35-3001A-01-01 Methane Sample-Draw Detector • 1OverviewThis operator’s manual describes the 35-3001A-01-01 methane sample-draw detector. This manual

2 • 35-3001A-01-01 Methane Sample-Draw DetectorDescriptionThis section describes the components of the methane sample-draw detector. Figure 1: Meth

35-3001A-01-01 Methane Sample-Draw Detector • 3External ComponentsThis section describes the sample-draw detector’s external components.HousingThe s

4 • 35-3001A-01-01 Methane Sample-Draw DetectorMain Circuit BoardThe main circuit board includes the detector/amp terminal strip, interconnect termin

35-3001A-01-01 Methane Sample-Draw Detector • 5counterclockwise to increase the flow and clockwise to decrease the flow.Status LEDsTwo status LEDs a